13

2026

-

11

Why a combine stops unloading, and where to look first

Author:


Nobody watches the unloading system until it fails. It runs fine all season, then the tank is full, the grain cart is waiting on the headland, you engage the lever, and nothing turns.

The scene repeats itself every harvest: the engine note drops, the auger stays still, the belt starts to smoke, and the first reaction is “the auger is shot”, followed by a wrench and a plan to pull the tube apart. Then the shield comes off and the real fault is a cracked tensioner bracket, a pulley sitting crooked, and a belt that has walked out of its groove. Weld the bracket, fit a new belt, and you are cutting again in twenty minutes. Strip the auger on that first diagnosis and you lose the afternoon.

So this article follows the order a technician uses in the field, not the order in a manual: identify the drive type, work through the eight causes that account for most failures, then run a five-minute check. A short list of jobs you should hand over to a workshop comes last.

First, identify your unloading drive type

The same symptom has three completely different causes depending on the machine. Get the drive type wrong and every check after it is wasted time.

Belt drive.The engine drives the unloading clutch through a belt, then the right-angle gearbox, then the vertical and horizontal augers that form the unloading tube. This is the layout on most small and mid-size machines, including the majority of Golddafeng 4LZ models. It is cheap to repair, and the faults sit in plain sight: belt, clutch, shear bolt.

Hydraulic motor drive.A pump feeds the unloading motor through a control valve, and the motor turns the gearbox. Common on high-capacity machines. Fast unloading, but the failures hide in pressure, oil temperature and internal leakage.

Electronic control with hydraulics.Most newer machines. The switch in the cab only sends a signal; solenoid valves, cylinders and the motor do the work, and the machine adds a fold-position limit switch and an interlock. If any electrical link in that chain is not made, nothing moves.

The eight causes we see most often, in order of frequency

1. The unloading belt slips, or breaks outright.You engage the lever, the engine loads up, the auger turns slowly or not at all, the pulley area gets hot, and there is a smell of burnt rubber with a glazed inner face on the belt. Usually the tension is low (a tired tensioner spring or a bent bracket), the belt is oily or dusty, or the pulley groove is worn wide. Once a groove has a step worn into it, a new belt will not grip either; the pulley has to go with it.

2. A shear bolt is cut, a key has rolled, or a spline is stripped.This is the machine telling you something is inside the tube. Twine, bag rope, wire, a stone, or wet grain packed into a solid plug has stalled the auger, and the overload protection acted first. It looks exactly like a broken drive: the engine note changes, the auger does not move, and sometimes it turns half a revolution and stops.

3. The grain tank gate is not fully open.The auger turns perfectly and no grain arrives, and the first assumption is worn flighting. Check the gate instead: a cylinder that does not complete its stroke, a dropped linkage pin, a manual gate nobody opened. The quick test is the inspection cover at the base of the tube. If the trough is dry, the problem is upstream at the gate. If the trough is full, the problem is the auger or the drive.

4. Hydraulic pressure is low.Hydraulic-drive machines only. Low oil level, a clogged suction strainer, a return filter due for change, a relief valve stuck open, or internal leakage in the unloading motor all produce the same feel: it turns but has no strength. Empty, the auger spins fast; the moment grain arrives it slows, oil temperature climbs, and after two or three loads the difference is obvious.

5. The electrical interlock is not satisfied.Newer machines will not unload unless the tube is fully swung out. A limit switch that is not depressed, a corroded plug, a blown fuse, burnt relay contacts, or a worn switch will keep the solenoid dead. The tell is a warning on the monitor, or no reaction at all, not even a change in engine note.

6. Grain has bridged in the tank.Most likely with damp grain, heavy weed load, or a high broken-grain count. The grain arches over and leaves a void underneath, so the auger runs dry while the tank still looks full. Slick tank walls, a small outlet and a machine parked dead level all make it worse.

7. Flighting worn thin, trough worn through, lower bearing collapsed.Older machines and any machine that has moved a lot of tonnes will get here. The decline is gradual: slower this year than last, then barely a trickle, with a metallic rasp and vibration in the tube.

8. The tube is not fully extended.Unloading while partly folded puts the tube in a bind, the auger runs out of line, and it turns slowly and noisily; in bad cases it takes the teeth out of the right-angle gearbox. A dry pivot pin, a deformed stop, or a leaking cylinder will leave the tube parked halfway.

A five-minute check order that starts with what you can see

One rule governs the order: check the cheap, visible things first, and do not open the tube until you have to.

  1. Listen before you touch a wrench. Engage the lever for three seconds. Load on the engine and a hot belt means the drive is slipping, so go to the belt. No change in engine note means nothing engaged, so check the clutch, solenoid and interlock. A change in note with a single clunk and no rotation means a stall, so check the shear bolt.
  2. Stop the engine and press the belt. More than 10–15 mm of deflection at the middle of the run is too loose. Look for oil, cracks, and a shiny glazed face.
  3. Remove the shield and look at the shear bolt, key and spline. A fresh break and an old one are easy to tell apart.
  4. Check the gate. Push the linkage by hand, or have someone watch whether the cylinder completes its stroke.
  5. Open the inspection cover on the tube and look at the inlet. This single step separates a gate problem from an auger problem.
  6. On a hydraulic machine, check oil level, both filters and oil temperature. Cycle the lever and listen for a continuous relief hiss; if it is there, pressure is escaping through the relief valve.
  7. Leave the electrics for last: fuses, relays, plugs, fold limit switch.

Table 1  Quick reference: symptom, likely cause, first check

Symptom

Most likely cause

Check first

Engine loads up, auger does not turn, belt hot

Belt slipping or broken

Belt tension, tensioner bracket, pulley groove

Engine note changes, auger still or half a turn

Plug in the tube, shear bolt cut

Clean-out cover, shear bolt, key

Auger turns normally, no grain arrives

Gate not open, or grain bridged

Gate linkage and cylinder, arch in the tank

Fast when empty, slow under load, hot oil

Low hydraulic pressure

Oil level, suction strainer, return filter, motor leakage

No reaction at all, monitor warning

Interlock not satisfied

Fold limit switch, plug, fuse, relay

Unloading slower every season

Worn flighting, worn trough

Flighting height, trough, lower bearing

Tube vibrates, metallic rasp

Tube not fully extended, auger binding

Pivot pin, stop, cylinder

 

Emergency fixes when the tank has to be empty today

The belt slips but still drives.Adjust tension on the spot rather than forcing it. Unload with the tube at its lowest position to reduce lift, split the load instead of running the tank out in one pass, and keep engine speed up instead of lugging at half throttle.

The auger is stalled.Shut down, remove the key, and wait until the auger has fully stopped. Open the clean-out cover at the end of the tube and work the plug loose from below with a stick or hook. Never by hand, never with a foot, never while it is turning. Afterwards bar the drive over by hand, using the pulley, and confirm it will turn a full revolution before you start the engine.

Grain has bridged.Stop the machine and break the arch with a long pole from the tank top or the inspection opening, with someone holding the ladder. If that is not possible, park on a slight slope, take part of the load out, and work the rest down by hand.

All three have one thing in common: engine off, key out. That is also the step most often skipped when the grain cart is waiting.

Four situations where you should stop and call a technician

Noise inside the right-angle gearbox, oil at the seal, teeth broken.Every extra minute runs the housing toward scrap, and the parts cost far more than the labour.

Hydraulic oil black, milky, or carrying metal.The pump or motor is already damaged; an oil change will not fix it.

Tube deformed, weld cracked, or sagging.This is the highest-stress point on the machine when the tank is full, and a field weld is not a repair.

Monitor alarms and improvised relay wiring.A cooked control unit means a two-week wait for parts. Machines still under warranty also belong here: cutting a shear bolt is one thing, but opening the shields and bypassing protection is how a warranty claim turns into an invoice.

End-of-season checks that prevent the breakdown

Before harvest.Set belt tension to spec. Put two spare shear bolts of the correct size in the toolbox. Grease the tube pivot pin and the gate linkage. Check oil level and both filters in one go. Pull the unloading switch plug apart and look for corrosion.

Every evening.Empty the tank and the unloading tube. Damp grain left overnight sets hard, and the first load next morning is the one that jams.

After harvest.Wash down, measure flighting height and replace anything worn past a third of its original depth, check the lower bearing for play, and oil the tube against rust.

In a wet season.Slow the unloading rate, hold engine speed steady, and do not leave grain sitting in the tank. The longer damp grain sits under its own weight, the more likely it bridges or packs.

FAQ: combine harvester unloading problems

The auger turns but no grain comes out. What is wrong?Start at the tank gate, then check for a bridge in the tank, then look at whether the inlet is packed with damp grain.

The unloading belt keeps breaking. Why?The belt is rarely the cause. Check the tensioner bracket, pulley alignment, groove wear, and whether something is jammed in the tube.

Unloading gets slower every year. Why?Work through flighting wear, belt slip, then hydraulic pressure. Do not start by ordering parts.

A new machine will not unload even with the tube out. Why?The fold limit switch is not depressed, or a plug is not seated, so the interlock never closes.

Is a warm gearbox normal during unloading?Warm is normal. Too hot to hold a hand on, together with noise, is not.

How do I unload very wet grain?Reduce intake, hold engine speed, and shorten the time grain spends in the tank. Do not wait until the tank is full to start unloading.

None of this is meant to turn an operator into a mechanic. One unloading failure in a season costs a full day, and a stored check order costs nothing. Keep Table 1 on your phone and walk through it on the headland; most machines give up their fault inside half an hour.

The unloading system on Golddafeng 4LZ combine harvesters follows the same belt-drive-plus-hydraulic-fold layout, and belts, tensioners and shear bolts are stock items. If a machine on your farm is not behaving, send the model, the hour meter reading and the symptom, and we will work it out machine by machine.